在使用之前，要將材料表面清理干凈，將浮灰和污漬去掉。如果使用鋁箔作為容器時，在加熱中，要運用不逾越3公分厚的鋁箔做容器。容器要進行填滿，不能接觸其它金屬部位，鋁箔容器應和其它鋁箔容器保持2公分的距離，在使用之前，如果容器有損壞，要及時更換，不要重復使用。
Before use, clean the surface of the material and remove any floating dust and stains. If aluminum foil is used as a container, it is necessary to use aluminum foil that does not exceed a thickness of 3 centimeters during heating. The container should be filled and should not come into contact with other metal parts. Aluminum foil containers should be kept at a distance of 2 centimeters from other aluminum foil containers. Before use, if the container is damaged, it should be replaced in a timely manner and not reused.
當鋁箔作為膠帶時，要在使用鋁箔膠帶之前將需要使用鋁箔膠帶的電子產品清理干凈，并用干凈的干抹布或者干毛刷將浮沉去掉。因鋁箔膠帶純度高，能消除電磁干擾，隔離電磁波對人體的傷害，避免不需要電壓與電流而影響功能。鋁箔膠帶的類型，規格要根據使用需要和具體條件，合理選取。輸送帶接頭要采用熱硫化膠接，以提高可靠性，保持較高的有效強度。在黏貼前，一定要確定好需要連接的位置，否則粘歪了再重新撕下來就比較麻煩。黏貼好之后要用手指在鋁箔膠帶上反復壓幾次，讓膠層充分發揮作用。輸送機的傳送輥簡直徑與傳送帶的小帶輪直徑應符合有關規定。鋁箔膠帶的材質為多元酯纖維，在重復使用或多次彎折后皆不易發生裂痕及損傷。不可以使鋁箔膠帶蛇行或蠕行，要保持拖輥，立輥靈活，張緊力要適度。
When using aluminum foil as adhesive tape, clean the electronic products that require aluminum foil tape before using it, and use a clean dry cloth or brush to remove the float and sink. Due to the high purity of aluminum foil tape, it can eliminate electromagnetic interference, isolate electromagnetic waves from harm to the human body, and avoid affecting functionality without the need for voltage and current. The type and specifications of aluminum foil tape should be reasonably selected based on usage needs and specific conditions. The conveyor belt joints should be bonded with hot vulcanized adhesive to improve reliability and maintain high effective strength. Before pasting, it is important to determine the position where the connection needs to be made, otherwise it will be more troublesome to tear it off again if the adhesive is crooked. After pasting, use your fingers to repeatedly press the aluminum foil tape several times to fully utilize the adhesive layer. The diameter of the conveyor roller and the small pulley of the conveyor belt should comply with relevant regulations. The material of aluminum foil tape is polyester fiber, which is not prone to cracking and damage after repeated use or multiple bending. It is not allowed to cause the aluminum foil tape to snake or creep, but to maintain the flexibility of the drag roller and the vertical roller, and the tension should be moderate.
當鋁箔作為隔熱服使用時，使用前，目測檢視防護服以確保所有裝備處于良好狀態，干凈并且沒有破損，如果有破損等問題，禁止使用。鋁箔隔熱服的面屏要處于良好狀態且玻璃處于正確位置。如果隔熱服內部溫度過高，應立即離開工作區域進入安全地帶，打開防護服以快速降低溫度。鋁箔隔熱服的存放應放在陰涼干燥處，不要折疊，以免防護服出現折痕，影響使用。
When using aluminum foil as insulation clothing, visually inspect the protective clothing before use to ensure that all equipment is in good condition, clean, and undamaged. If there are any issues such as damage, use is prohibited. The surface screen of the aluminum foil insulation suit should be in good condition and the glass should be in the correct position. If the internal temperature of the thermal insulation clothing is too high, immediately leave the work area and enter the Anzen Chitai. Open the protective clothing to quickly reduce the temperature. Aluminum foil insulation clothing should be stored in a cool and dry place, and should not be folded to avoid creases in the protective clothing that may affect its use.
This article is a friendly contribution from aluminum coil manufacturers. For more information, please click on: http://m.ahxsxljk.com Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned
